小半径弯管弯胀复合成形研究

为解决小半径弯管内侧起皱、外侧减薄的成形缺陷,提出了一种弯胀复合成形的方法。通过几何关系解析了初始弯曲半径和初始管坯直径与最终管径和最终弯曲半径之间的关系,确定了初始弯曲半径的取值范围。采用有限元与实验相结合的方式研究了不同初始弯曲半径对零件壁厚分布的影响,分析了胀形过程中零件弯曲处及直壁处的变形规律。最终发现:初始弯曲半径越大,零件的最终减薄越小,胀形过程中弯曲处内外侧发生均匀减薄,直壁处内侧减薄明显大于外侧减薄。     

ZL205A合金舱体低压工艺设计及数值仿真应用

针对某ZL205A合金舱体铸件壁薄难充型、壁厚差异大、易产生裂纹等特点,设计了低压底注式浇注工艺。采用立筒缝隙式浇注系统分配充型过程中合金的流量,局部厚大部位放置成形冷铁加快该部位的冷却速度,以控制铸造缺陷的产生。利用ProCast数值仿真软件对工艺进行仿真计算,成功预测了缺陷的产生位置,对工艺方案进行优化,包括倒角过渡、改变型砂使用等,并在优化方案的基础上浇注了舱体铸件,铸件质量良好,没有缩松、缩孔、裂纹等缺陷,符合相关技术要求。     

某型飞机空中受油管自动开锁故障分析

针对某型飞机空中受油管在收上位置钢珠锁自动开锁故障,对空中受油管液压收放系统、电路控制系统、收上位置钢珠锁工作原理进行分析,比对钢珠锁开锁压力理论计算和收放系统回油压力测试试验结果,找出空中受油管收上位置钢珠锁自动开锁原因,提出改进建议。     

风-雨耦合环境超高层三塔连体建筑雨压分布研究

以中国东南沿海某超高层三塔连体建筑为研究对象，以风-雨双向耦合算法为核心，基于计算流体动力学技术采用连续相和离散相模型进行风场和雨场的迭代模拟。首先基于9种风雨组合工况进行三塔连体建筑非定常脉动风场模拟，探讨超高层三塔连体建筑平均风压分布、表面速度流线和流场干扰机理。然后对比研究不同风雨组合工况下主塔表面雨滴附着数量、雨滴冲击力和雨压系数的分布规律，揭示风-雨耦合场中结构表面速度流线、雨滴运行轨迹和最终速度的作用机理。最后提炼出超高层三塔连体建筑最不利风-雨组合工况，并给出对应的雨压系数取值建议。研究表明：风-雨耦合环境下超高层连体建筑迎风面雨荷载作用最为显著，此时雨荷载与风荷载最大比值可达23.81%，局部测点最大雨压系数达到0.301，100 a重现期风速和强大暴雨组合为风-雨耦合作用的最不利组合工况。     

弹片热机械疲劳试验方法研究及设计

针对弹片的热机械疲劳（TMF）试验要求，采用机械设计技术、机电技术、冷却技术、计算机技术和数据采集技术，提出了压力载荷和热载荷的加载方法，建立了2种载荷5个试验件的并联试验控制系统，并设计了弹片热机械疲劳试验器。试验结果表明:该系统能够同时模拟服役环境下弹片的压力载荷和热载荷。利用该试验系统进行了弹片的热机械疲劳试验，试验结果再现了弹片在服役状态下的失效模式。试验系统具有良好的重复度、较高的加载频率和加载精度。压力载荷最大相对误差为2.4%，绝对误差小于0.5N。温度载荷最大相对误差为3.55%，最大绝对误差为3.89℃。      

基于两相流模型的挤压油膜阻尼器空化流场特性数值模拟

基于气液两相流理论中的Mixture模型和Zwart-Gerber-Belamri空化模型,采用动网格技术建立了两端开口中心槽供油型挤压油膜阻尼器三维非定常空化流场求解模型。数值模拟表明:随着阻尼器内环进动,考虑两相流动的油膜低压区在中心槽的两侧产生两道对称的条状负压带,条状带内具有较高的气相体积分数;阻尼器低压区的压力和气相体积分数对进油孔位置十分敏感,阻尼器油膜力和流场气穴比的变化频率与进油孔数密切相关。内环同心进动半径、进动频率对阻尼器空化流场影响的数值计算表明,进动半径和频率的增大均会使得流场内的空化现象加剧,同时气穴比的相位滞后现象愈加显著。      

回流燃烧室流动特性试验

为了揭示有/无燃烧状态下燃烧室热态和冷态流场的特征和流动特性，针对某型回流燃烧室单头部试验件，使用粒子图像测速仪（PIV），测量燃烧室燃烧状态下不同截面处的热态流场，以及没有燃烧状态下不同截面处的冷态流场，探讨不同总压损失系数对回流燃烧室热态/冷态流场特征及流动特性的影响。研究表明:随着总压损失系数的增大，冷态条件下各截面流场结构基本保持不变，如射流孔穿透深度、射流角度、回流区位置及大小、流线等基本保持一致，但是各位置点速度大小逐渐增大。热态条件下各截面流场随着总压损失系数增大，流场结构也基本保持不变；相同总压损失系数时，热态流场与冷态流场存在差异，燃油喷射与气流的相对运动将会对燃烧室头部的流场结构造成影响，速度较冷态流动时略微增大。      

Effects of Mach numbers on Magnus induced surface pressure

Experimental and numerical methods were used to investigate the Magnus phenomena over a spinning projectile. The pressure force acting on the surface of a spinning projectile was measured for various cases by employing a relatively novel experimental technique. A set of miniature pressure sensors along with a data acquisition board, battery and storage memory were placed inside a spinning model and the surface pressure were obtained through a remotely controlled system. Circumferential pressures of the model for both rotational and static conditions were obtained at two different free stream Mach numbers of 0.4 and 0.8 and at different angles of attack. The results showed the ability of this new test method to measure the very small Magnus force via surface pressures over the projectile. The results provide a deep insight into the flow structure and illustrate changes in the cross-flow separation locations as a result of rotation. Similar results were obtained by the numerical simulations and were compared with the experimental data.     

Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

静压气浮轴承工程设计方法研究

静压气浮轴承是惯性器件测试平台回转支撑轴系的关键部件，其承载能力和回转精度对惯性器件测试的准确性有着重要的影响，目前，静压气浮轴承设计、计算过程复杂，为提高设计效率，简化设计方法，在满足静压气浮轴承性能的条件下，推导了静压气浮轴承工程计算公式，在此基础上，设计了一款双向止推空气轴承，确定了几何参数，计算了空气静压径向轴承、空气静压止推轴承的轴承承载力、刚度、耗气量及摩擦力矩，并与有限元仿真结果进行了对比分析，验证了该设计方法的有效性。